Home → TAIZHOU Jusheng Mould & PLASTIC Specification → Injection mould design → Mold DFM analysis to short the injection mold making lead time
Mold DFM analysis to short the injection mold making lead time
What is mold and plastic product DFM analysis?
DFM is “Design for Manufacturability”. Mold and plastic product DFM analysis is plastic product design for injection mold manufacturability and injection molding manufacturability. On below page, we will call our “Mold and plastic product DFM analysis” as mold DFM.
What TAIZHOU Jusheng Mould & PLASTIC injection mold factory do for the mold DFM?
Plastic product draft analysis as all of the plastic product for plastic injection molding should have the draft for mold release, otherwise there will be scratch on plastic product surface, sticking on core or cavity
Injection analysis for plastic injection product such as gate location ,venting, injection defect analysis, cooling etc.
Plastic injection ejection analysis
Injection mold making risky analysis
Injection molding risky analysis
Plastic injection mold structure analysis and description including parting line, slider, lifter, gate, cooling and venting etc.
Why we should do the mold DFM analysis and Why this can short the lead time?
Mold DFM analysis is professional process to evaluate if the plastic product is suitable for injection mold design and injection mold making.
Mold DFM analysis is good process to communicate the plastic product appearance as we will tell customer the parting line, ejection location, sliders location and angle lifters location. So far as we know there is parting line on sliders area and angle lifters area. Also on ejection locations, there is ejection pin mark.
Mold DFM analysis is good process to foreknow the risky of injection mold making and injection molding, it is necessary process to prevent the cost waste on injection mold manufacturing and injection molding.
Mold DFM analysis have good communication between customers and TAIZHOU Jusheng Mould & PLASTIC injection molder for mold structure, gate location, parting line, ejection location, slider location and lifters location, this process short communication lead time of mold design.
Mold DFM analysis fully analyse the risky of customers’ invest of plastic product design, plastic mold making and plastic molding as well as plastic product development.
Mold DFM analysis prevent the risky of injection mold making and injection molding, this means we save lead time by preventing the rework and cost.
Inquiry TAIZHOU Jusheng Mould & PLASTIC plastic mould manufacturer now for plastic mould making and injection molding by send email to
Taizhou Jusheng Mould and Plastic Co., Ltd.
Email: [email protected]
WhatsApp: 0086-188-5866-1772
Website: http://www.MouldOne.com http://www.JacksonMould.com
Injection mold location ring and sprue design
Home → TAIZHOU Jusheng Mould & PLASTIC Specification → Injection mould design → Injection mold location ring and sprue design
Injection mold location ring and sprue design
Injection mold location ring design
Unless specifically required, otherwise all mold inch (DME) or metric (HASCO) location ring must refer to the following standard size and made with S50C(1050) steel.
DME mold standard sprue bushing should be used as A-1 picture show preferentially
Injection mold location ring A-4
Injection mold location ring A-4
Injection mold location ring A-3
Injection mold location ring A-3
Injection mold location ring A-2
Injection mold location ring A-2
Injection mold location ring A-1
Injection mold location ring A-1
HASCO mold standard location ring design
Injection mold location ring B-1
Injection mold location ring B-1
Injection mold location ring B-2
Injection mold location ring B-2
Injection mold location ring B-3
Injection mold location ring B-3
Injection mold sprue bushing standard
Mold sprue bushing steel: H-13 (HRC50-54), if plastic product resin is PVC, POM, need to use 420 steel and hardness is HRC48-52
DME mold standard sprue, SR size refer to the injection machine specification
DME mold standard sprue bushing
DME mold standard sprue bushing
Sprue bushing have to be positioned if the mold runner is round or there is runner on sprue bushing.
Spring bushing location-injection mold
Spring bushing location-injection mold
D=4.76mm in DME mold standard
D=6.00mm in HASCO mold standard
HASCO mold standard sprue bushing , SR size refer to the injection machine specification
HASCO mold standard sprue bushing
HASCO mold standard sprue bushing
Taizhou Jusheng Mould and Plastic Co., Ltd.
Email: [email protected]
WhatsApp: 0086-188-5866-1772
Website: http://www.MouldOne.com http://www.JacksonMould.com